Certified quality management system
Measurement Technology
Measurement engineering is a major division of Sourcetronic. Your measurement engineering specialist, specialized on highly diverse measurements, such as resistor measurements, LCR, high voltage, isolation resistors, security tests but as well multimeters, oscilloscopes and software.
- Test cage with transparent hood for test instruments of the 36 series
- Fully assembled with safety switch (2 paths)
- Positive protection against contact per EN 50191
- Gas springs for damping and end-position damping
- Interior (W x H x D): 550 x 350 x 450 mm
- Test connections HV1 and HV2/PEX1 with safety sockets and quick-action test clamps
- Connecting leads for the test instrument included (safety circuit, 2 x HV cable, 2 m)
- IP30, weight: 19.0 kg
- Max. rated values HV/ISO: 7 kV AC / 10 kV DC, max. 10 A
- Test cage with transparent cover
- Completely assembled with safety switch (2 paths)
- Mandatory protection against accidental contact according to EN 50191
- Gas springs for damping and end-position damping
- Interior (W x H x D): 800 x 350 x 450 mm
- Safety switch connections terminated on terminal block
- IP30, weight: 21.3 kg
- Max. rated values HV/ISO: 7 kV AC / 10 kV DC, max. 10 A
- Test cage with transparent hood
- Fully assembled with safety switch (2 paths)
- Positive protection against contact per EN 50191
- Gas springs for damping and end-position damping
- Interior (W x H x D): 1,000 x 350 x 450 mm
- Safety switch connections wired to contact terminal
- IP30, weight: 24 kg
- Max. rated values HV/ISO: 7 kV AC / 10 kV DC, max. 10 A
- Test cage with transparent hood
- Completely assembled with safety switch (2 channels)
- Mandatory protection against accidental contact according to EN 50191
- Gas springs for damping and end-position damping
- Interior (W x H x D): 650 x 530 x 600 mm
- Safety switch connections terminated on terminal block
- IP30, Weight: 27 kg
- Max. rated values HV/ISO: 7 kV AC / 10 kV DC, max. 10 A
- Test cage with transparent hood
- Completely assembled with safety switch (2 paths)
- Mandatory contact protection according to EN 50191
- Gas springs for damping and end-position damping
- Interior (W x H x D): 800 x 530 x 600 mm
- Safety switch connections applied to contact terminal
- IP30, weight: 27 kg
- Max. rated values HV/ISO: 7 kV AC / 10 kV DC, max. 10 A
- Test cage with transparent hood
- Completely assembled with safety switch (2 paths)
- Inevitable protection against accidental contact according to EN 50191
- Gas springs for damping and end-position damping
- Interior (W x H x D): 1,000 x 530 x 600 mm
- Safety switch connections connected to terminal block
- IP30, weight: 39 kg
- Max. rated values HV/ISO: 7 kV AC / 10 kV DC, max. 10 A
- Test cage with vertical lifting door and rear wall wiring
- Completely assembled with safety switch (2 paths)
- Mandatory protection against accidental contact in accordance with EN 50191
- Balanced counterweights for ergonomic working
- Movable front made of transparent plastic
- Wiring compartment in the floor and rear area, floor and rear wall can be unscrewed
- Interior (W x H x D): 1,000 x 900 x 1,000 mm
- Safety switch connections terminated on terminal block
- IP30, weight: approx. 100 kg
- Max. ratings: 7 kV AC / 10 kV DC, max. 10 A
- Two-hand control for test stations with ergonomic control buttons
- Standard-compliant spacing and control recesses
- With supply cable and connector plug for UH36 and UX36
- Mains supply cable length: 1.5 m
- Selectable supply cable length: 2.5 m or 5 m
- Connection cable for remote control of the test device via PC or PLC
- 9-pin SUB-D, plug / socket
- Cable with RX/TX crossed
- Remote control via DataView, ASCII commands or custom application (ETL driver: DLL, ACTIVE-X, LabVIEW)
- Selectable cable length: 2 m, 5 m or 10 m
- Safety circuit connector UH36, unassigned, for customer-specific assembly
- 3 different safety circuits can be implemented through wiring
- Testing with test guns: 2 bridges (Pin 4-5 and Pin 6-7)
- Testing with test cage or two-hand operation: 2 normally open contacts (Pin 2-6 and Pin 3-5)
- Automation solution: 2 normally open contacts / bridges (Pin 1-6 and Pin 5-8)
- Replacement key for the mains switch, for the Series 36
- Scope of delivery: 2 keys
- HV Test: 5kV AC
- Release current: 200mA
- 2k VA power / potential free
- Burning function and ramp
- Digital voltage control
- RS232, digital I/O (SPS), CAN
- Software, DLL, LabView, Active-X (option)
- Work place according to EN 50191
- High-voltage tester with dry-type transformer, 6 kV AC / 200 mA / 1,200 VA
- Test voltage 100 - 6,000 V AC, test current 0.5 - 200 mA
- Controlled, potential-free high voltage for operation with test pistols
- Ramp function, shutdown via limit value and peak detection
- Contacting and cable break monitoring, automatic start for test pistols
- Safety circuit according to EN 50191 with two forcibly guided safety relays
- Remote controllable (ASCII, Windows DLL, .NET Framework Assembly, DataView)
- 15 freely programmable parameter sets