Certified quality management system
Hipot Tester UX36-AC-05-0500-TPT
€9,980.00*
Details
+49 421 277 9999
Product information "Hipot Tester UX36-AC-05-0500-TPT"
The UX36 is a high-voltage test instrument (hipot tester) with dry-type transformer for AC high-voltage testing with test voltages from 100 to 5,000 V AC, test currents from 1 to 500 mA and a power of 2,500 VA. The test voltage is regulated and the high voltage is potential-free, which makes the unit suitable for operation with test guns. A ramp function as well as contact and cable break monitoring support reliable test processes, and the safety circuit is designed in accordance with EN 50191. The unit is suitable for stand-alone operation as well as remote control via PC software or customer-specific applications.
Highlights
- HV AC - high-voltage test: 100 - 5,000 V AC, 1 - 500 mA, potential-free, ramp
- Shutdown via limit value and peak detection
- Ramp function, keypad lock, minimum current monitoring
- Remote controllable (ASCII, Windows DLL, .NET Framework Assembly, DataView)
- Source-sense operation, automatic start for test guns
- Contact and cable break monitoring
- 15 freely programmable parameter sets
- Fault indication: acoustic, optical and via interface
- Safety circuit with two positively guided safety relays
Technical data and standards
Test voltage |
|
| Adjustment range: | 100 - 5,000 V AC |
| Voltage stability: | regulated output voltage, continuous PI control for a constant test voltage regardless of mains voltage fluctuations |
| Power: | 2,500 VA |
Test current |
|
| Adjustment range, limit: | 1 - 500 mA |
Extended functions |
|
| Ramp function: | The voltage ramp can be switched on, and its parameters (e.g. rise and fall time) are freely selectable. The ramp function ensures a particularly gentle test and is required whenever a product standard specifies a particular voltage profile |
| Breakdown voltage detection: | The voltage value at which a fault was detected is held flashing in the display |
| Fault detection: | shutdown via limit value and peak detection. In addition to exceeding the current limit, a special overcurrent detection also triggers a fault, so even low-energy breakdowns are reliably detected |
| Contact monitoring: | Monitoring of the contact to the test object |
| Cable break monitoring: | Monitoring of the test leads for cable breaks; high-voltage leads in 4-wire technique (source-sense) for maximum process reliability |
| Keypad lock: | Prevents accidental changes to the test parameters and can be configured individually, e.g. all keys can be locked or individual functions (e.g. calling up test programs) remain permitted |
| Automatic start: | The start signal is triggered by pressing the test guns against the test object. The voltage is only switched on once both test probes are safely in contact with the test object. This protects the test object from overvoltage spikes and ensures the required test time |
| Current and voltage measurement: | directly on the high-voltage side for precise test results |
| Potential-free operation: | high voltage is potential-free, a prerequisite for operation with test guns and maximum safety for the operator |
Standards and electrical safety |
|
| EN 50191: | safety circuit designed as required by the standard, with two positively guided safety relays |
Operation, start options & interfaces
Advanced device setup |
|
| Individual settings: | start options, keypad lock, language and mode selection for external printer, behaviour of the digital inputs and outputs, ramp options, options for contact and cable break monitoring, brightness of the display elements and more |
| Update capability: | updatable via interface for customer-specific changes and updates |
Interfaces |
|
| Remote control: | via PC software (ETL DataView user interface), a customer's own application (DLL, C#, .NET, LabVIEW), simple command parameters (ASCII) or digitally from a PLC (digital I/O) |
Related products
- Test cage with transparent cover
- Completely assembled with safety switch (2 paths)
- Mandatory protection against accidental contact according to EN 50191
- Gas springs for damping and end-position damping
- Interior (W x H x D): 800 x 350 x 450 mm
- Safety switch connections terminated on terminal block
- IP30, weight: 21.3 kg
- Max. rated values HV/ISO: 7 kV AC / 10 kV DC, max. 10 A
- Devices: hipot testers 36 series
- Signal lamp: red / green
- Conforming to all standards: VDE0104, EN50191
- Status:
- READY FOR OPERATION
- READY TO SWITCH ON
- IN OPERATION
- Voltage: 230V
- Cable length: 2m
- Test cage with transparent hood
- Fully assembled with safety switch (2 paths)
- Positive protection against contact per EN 50191
- Gas springs for damping and end-position damping
- Interior (W x H x D): 1,000 x 350 x 450 mm
- Safety switch connections wired to contact terminal
- IP30, weight: 24 kg
- Max. rated values HV/ISO: 7 kV AC / 10 kV DC, max. 10 A
- Test cage with vertical lifting door and rear wall wiring
- Completely assembled with safety switch (2 paths)
- Mandatory protection against accidental contact in accordance with EN 50191
- Balanced counterweights for ergonomic working
- Movable front made of transparent plastic
- Wiring compartment in the floor and rear area, floor and rear wall can be unscrewed
- Interior (W x H x D): 1,000 x 900 x 1,000 mm
- Safety switch connections terminated on terminal block
- IP30, weight: approx. 100 kg
- Max. ratings: 7 kV AC / 10 kV DC, max. 10 A
- Test cage with transparent hood
- Completely assembled with safety switch (2 channels)
- Mandatory protection against accidental contact according to EN 50191
- Gas springs for damping and end-position damping
- Interior (W x H x D): 650 x 530 x 600 mm
- Safety switch connections terminated on terminal block
- IP30, Weight: 27 kg
- Max. rated values HV/ISO: 7 kV AC / 10 kV DC, max. 10 A
- Test cage with transparent hood
- Completely assembled with safety switch (2 paths)
- Mandatory contact protection according to EN 50191
- Gas springs for damping and end-position damping
- Interior (W x H x D): 800 x 530 x 600 mm
- Safety switch connections applied to contact terminal
- IP30, weight: 27 kg
- Max. rated values HV/ISO: 7 kV AC / 10 kV DC, max. 10 A
- Test cage with transparent hood
- Completely assembled with safety switch (2 paths)
- Inevitable protection against accidental contact according to EN 50191
- Gas springs for damping and end-position damping
- Interior (W x H x D): 1,000 x 530 x 600 mm
- Safety switch connections connected to terminal block
- IP30, weight: 39 kg
- Max. rated values HV/ISO: 7 kV AC / 10 kV DC, max. 10 A
- Two-hand control for test stations with ergonomic control buttons
- Standard-compliant spacing and control recesses
- With supply cable and connector plug for UH36 and UX36
- Mains supply cable length: 1.5 m
- Selectable supply cable length: 2.5 m or 5 m
- Connection cable for remote control of the test device via PC or PLC
- 9-pin SUB-D, plug / socket
- Cable with RX/TX crossed
- Remote control via DataView, ASCII commands or custom application (ETL driver: DLL, ACTIVE-X, LabVIEW)
- Selectable cable length: 2 m, 5 m or 10 m
- Safety circuit connector UH36, unassigned, for customer-specific assembly
- 3 different safety circuits can be implemented through wiring
- Testing with test guns: 2 bridges (Pin 4-5 and Pin 6-7)
- Testing with test cage or two-hand operation: 2 normally open contacts (Pin 2-6 and Pin 3-5)
- Automation solution: 2 normally open contacts / bridges (Pin 1-6 and Pin 5-8)
- Replacement key for the mains switch, for the Series 36
- Scope of delivery: 2 keys
- HV test gun with automatic start, contact check and cable break monitoring
- HV cable, 2-pole, blue (D = 9.6 mm)
- HV plug HVP06C (D = 6 mm), 2-pin, for plugging into the test instrument
- Max. operating voltages: 7 kV AC / 10 kV DC, max. 10 A
- Start signal generated when pressed against the test object; high voltage only switches on after contact (with suitable test instrument)
- Tungsten test probe (10 mm, extendable), retracted into an arc-resistant Teflon shaft between tests
- Trigger secured against accidental actuation
- Selectable cable length: 2 m, 3 m, 5 m or 10 m (other cable lengths on request)
- HV cable, 2-pole, blue (D = 9.6 mm), with open cable end for self-assembly
- HV plug HVP06C (D = 6 mm), 2-pin, for plugging into the test instrument
- Max. operating voltages: 7 kV AC / 10 kV DC, max. 10 A
- Selectable cable length: 2 m, 3 m, 5 m or 10 m (other cable lengths on request)
- HV cable, 2-pole, blue (D = 9.6 mm)
- HV plug HVP06C (D = 6 mm), 2-pin, for plugging into the test instrument
- Opposite end with 4 mm lamella plug, e.g. for attaching a test clamp
- Max. operating voltages: 7 kV AC / 10 kV DC, max. 10 A
- Selectable cable length: 2 m, 3 m, 5 m or 10 m (other cable lengths on request)
- Standard-compliant, multi-vendor calibration based on ISO 17025
- Calibration of Hipot Tester / HV tester
- Traceable to DKD
- Cleaning and adjustment
- Repair service
- Drivers, example programs, and programming manual
- Functions: high-voltage test, protective earth test, insulation test, current consumption test, 2-wire/4-wire, user interface, external relay matrix
- Compatible devices: UH36, UB36, UG36, RS36, ST400
- Conforming to all standards
- Emergency stop for tester
- Load: 16 A
- Cable length: 5 m
- Including cable set for safety tester ST400 series
- Dimension (W/H/D):
Outside: 450 / 515 / 495 mm
Inside: 360 / 350 / 450 mm - Completely mounted and wired for plug&play
- PVC design-housing
- Viewable transparent swinging hood
- Damping gas spring
- Safety limit switch
- CE conform with EN 50191
- Rectangle design
- "No unauthorised entry"
- Material: plactic
- Size: 200mm x 300mm
- Colour: red/white
- Log printer in own plastic table casing
- Not to be built-in.
- Baud rate 9600
- Portable posts chain
- Convex base plate
- Colour: Yellow-Black
- Two-parts
- Height: 1100mm / D=32cm
- With safety socket
- For easy testing of test objects
- L and N bridged/connected
- In plastic casing
- Side mounting for test waggon or table
- Ergonomically placed
- HV probe type: HTP
- Side: left
- Colour: white
- HV Tester: UB36, UG36, UH36, UX36
- Start via control-IO
- With plug: SUB-D 9-pole
- Access to control interface
- Cable length: 2m
- Test cage with transparent hood for test instruments of the 36 series
- Fully assembled with safety switch (2 paths)
- Positive protection against contact per EN 50191
- Gas springs for damping and end-position damping
- Interior (W x H x D): 550 x 350 x 450 mm
- Test connections HV1 and HV2/PEX1 with safety sockets and quick-action test clamps
- Connecting leads for the test instrument included (safety circuit, 2 x HV cable, 2 m)
- IP30, weight: 19.0 kg
- Max. rated values HV/ISO: 7 kV AC / 10 kV DC, max. 10 A
- Test cage with transparent hood
- Fully assembled with safety switch (2 paths)
- Positive protection against contact per EN 50191
- Gas springs for damping and end-position damping
- Interior (W x H x D): 550 x 350 x 450 mm
- Safety switch connections wired to contact terminal
- IP30, weight: 19.0 kg
- Max. rated values HV/ISO: 7 kV AC / 10 kV DC, max. 10 A
- Robust 2-wire matrix
- Measuring points freely connectable
- Test connection via Harting plug
- Continuity tests
- High voltage tests
- Insulation resistance tests
- Surge voltage tests
- HV cable, 2-pole, blue (D = 9.6 mm)
- HV plug HVP06C (D = 6 mm), 2-pin, for plugging into the test instrument
- With contact clamp (solid design) on the opposite end for contacting the test object, clamp width: 38 mm
- Max. operating voltages: 7 kV AC / 10 kV DC, max. 10 A
- Selectable cable length: 2 m, 3 m or 10 m (other cable lengths on request)
- Remote control of Series 36 devices
- Create and edit test plans
- Menu-guided test plan selection: mouse/keyboard/scanner
- Administrator administration and user management
- Visualized test run and storage of reports
- Compatible devices: UH36, UX36, ZPA36
- Export formats: XML, PDF, CSV, HTML
- Remote control via: RS-232
- Languages: German, English
- Operating system: Windows
- HV-Cable, two-pole
- Length 2 m
- HV-plug HVP06C
- 2 x counter plug
- 7 kV AC / 10 kV DC, max. 10 A
- Test cage with transparent hood
- Fully assembled with safety switch (2 paths)
- Positive protection against contact per EN 50191
- Gas springs for damping and end-position damping
- Interior (W x H x D): 330 x 350 x 450 mm
- Safety switch connections wired to contact terminal
- IP30, weight: 14.5 kg
- Max. rated values HV/ISO: 7 kV AC / 10 kV DC, max. 10 A
- HV cable, 2-pole, blue (D = 9.6 mm), with open cable end for self-assembly
- HV angled plug HVP06CW (D = 6 mm), 2-pin, for plugging into the test instrument
- Max. operating voltages: 7 kV AC / 10 kV DC, max. 10 A
- Selectable cable length: 2 m, 3 m, 5 m or 10 m (other cable lengths on request)
- Test cage with transparent hood for test instruments of the 36 series
- Fully assembled with safety switch (2 paths)
- Positive protection against contact per EN 50191
- Gas springs for damping and end-position damping
- Interior (W x H x D): 330 x 350 x 450 mm
- Test connections HV1 and HV2/PEX1 with safety sockets and quick-action test clamps
- Connecting leads for the test instrument included (safety circuit, 2 x HV cable, 2 m)
- IP30, weight: 14.5 kg
- Max. rated values HV/ISO: 7 kV AC / 10 kV DC, max. 10 A
- Including cable set for safety tester ST400 series
- Dimension (W/H/D):
Outside: 670 / 515 / 495 mm
Inside: 565 / 350 / 450 mm - Viewable transparent swinging hood
- Damping gas spring incl. final pos. damping
- Safety limit switch
- CE conform with EN 50191
- Triangle design
- With flash arrow
- Material: plactic
- Size: 200mm x 200mm
- Colour: yellow/black
- DIN 40008
- Dolphin clamp made of brass with all-round insulation
- Toothed jaw for coarse contact points and fine-wire surface, suitable for contact points up to 30 mm in diameter
- Extended design specifically for plugging onto Ø 4 mm lamella plugs
- Available in black and red
- With safety socket and test nipple
- For easy testing of test objects
- In plastic casing
- Devices: 36 series
- Mounted on test trolley
- Total hight of lamps 1850mm
- Standard: EN 50191, VDE0104
- Lights: Red/Green
- Function: operation, switch on, ready
- Cable length: 2m
- Side mounting for test waggon or table
- Ergonomically placed
- HV probe type: HTP
- Side: right
- Colour: white
- HV Tester: UB36, UG36, UH36, UX36
- With foot protection cover
- Start via control-IO
- With plug: SUB-D 9-pole
- Access to control interface
- Cable length: 2m
- Rectangle design
- "Danger High Voltage"
- Material: plactic
- Size: 74mm x 210mm
- Colour: yellow/black
- EN50191 / DIN 40008
- HV test gun HTP06C with automatic start, contact check and cable break monitoring
- HV cable, 2-pole, blue (D = 9.6 mm)
- Without HV plug for plugging into the test instrument, open cable end
- Max. operating voltages: 7 kV AC / 10 kV DC, max. 10 A
- Selectable cable length: 2 m or 3 m (other cable lengths on request)
- Drivers, example programs and programming manual
- Functions: high-voltage test, protective earth test, insulation test, current consumption test, 2-wire/4-wire, user interface, external relay matrix
- Compatible devices: UH36, UB36, UG36, RS36, MR36, ST400