Accessories Frequency Inverter
AC-Drives are used in many applications and always have to work fully functional and reliable. In practice, there are effects such as radiant emissions, voltage-spikes, braking operation of motors with large loads and interference effects in the motor supply. To work always reliable and safe, it is necessary to counter these effects. Sourcetronic therefore offers a wide spectrum of high quality accessories for AC-Drives. These are EMI Input and output filters, brake units and brake resistors. External Brake units are used in applications where the connected motor has to deal with a heavy load or fast load changes. The Brake unit protects the intermediate-circuit of the AC-Drive from a surplus of energy, which is fed back by the motor. Through the brake resistor the energy surplus is then converted into thermal energy and delivered to the environment. The AC-Drives Accessories are all-purpose accessories and not only compatible to Sourcetronic AC-Drives.
- Frequency Inverter Quick Service
- Installation, commissioning, trial operation
- Instruction of the operating personnel
- Identification of error causes
- Reduction of subsequent and repeat faults
- Maintenance, servicing and retrofitting of systems
- Lifecycle management of drive technology
- Around-the-clock service": 24/7 monitoring service of plants
- Consulting and design drive technology
- Project planning Electrical engineering
- E-construction ePlan P8
- Programming/visualisation (PLC/HMI/JAVA)
- Monitoring, control and regulation systems
- Sensor consulting
- Processing of tenders with focus on drive technology, automation, pump controls
- Determination of energy saving potentials
- Planning, construction, delivery and installation of control systems
- Installation & Commissioning
- Configuration and parameterisation
- Switch cabinet construction
- Electrification of entire construction sites
- Frequency converter exchange
- Standard-compliant documentation
- Instruction of the operating personnel
- Compatible with frequency inverters of the ST600 series
- Compatible with PLC Siemens S7-1200 or S7-1500 with TIA Portal V15
- The Profinet card is connected via two RJ45 sockets
- Compatible with ST600 frequency inverter series
- PROFIBUS standard: DP
- Connection via Sub-D-9 socket
- Transmission rate: 9.6kbit/s to 12Mbit/s
- Up to 32 nodes (without repeater) and 127 nodes (with repeater) in one segment of the network
- 24V power supply card SPS501-24 recommended as a supplement
- Compatible with ST600 series frequency inverters
- For ABZ incremental encoders with differential, push/pull or OC output
- Voltage: 5/12VDC switchable via SW1
- 5V differential frequency divider output, configurable from 1:1-2255
- Intuitive installation thanks to plug and play: just plug in and go
- Compatible with ST600 series frequency inverters
- For ABZ incremental encoders with differential, push/pull or OC output
- Voltage: 24V
- 5V differential frequency divider output, configurable from 1:1-2255
- Intuitive installation thanks to plug and play: just plug in and go
- Compatible with ST600 series frequency inverters
- PG card for brushless resolver
- Excitation voltage 7 VRMS, frequency 10kHz
- Recommended transfer ratio: 0.5
- Resolver output voltage 1±0.2Vpp
- 5V differential frequency divider output ABZ, configurable from 1:1-2255
- Intuitive installation thanks to plug and play: just plug in and go
- Compatible with ST600 series frequency inverters
- Sinusoidal encoder with/without C/D signals
- Voltage: 5VDC
- Easy installation thanks to plug and play
- Telefonische Beratung
- Auslegung und Inbetriebnahme
- Individuelle Parametrierung
- Programmbetrieb
- Parameterliste
- Compatible with ST600
- 4 digital inputs
- 1 digital output
- 2 relays with one normally open contact each.
- 1 connection for a PT100 temperature sensor
- 1 connection for a PT1000 temperature sensor
- Compatible with ST600 series frequency inverters .
- Connection via Sub-D-9 female
- termination resistor adjustable by DIP switch
- Transmission rate: 9.6kbit/s to 12Mbit/s
- Compatible with ST600 series of frequency converters
- High resolution graphical LCD control panel
- Connection via RJ45