Certified quality management system
Safety Tester
If you need to carry out electrical safety test in accordance with EN 60335, EN 61010, EN 60601, EN 60598 or other national and international norms, then you are at the right place. EN 60335 is a European regulation for safety of electrical devices. Tests in accordance with EN 60335; e.g. the protective conductor test, high voltage test and function test, are carried out on the whole device after assembly.
The robust, fully automatic Electrical Safety Tester ST400 ensures fast testing cycles incl. documentation (backtracking of data – Traceability). In addition to that, the ST400 Electrical Safety Tester also disposes two USB- Interfaces, LAN, RS232 and digital, as well as analogue I/O ports. I/O tests are ideally used to automatically pilot external systems. The test procedure with an Electrical Safety Tester results as follows: Connect the testee (device under test), chose the settings for the test program (automatic barcode if provided), test and save test protocol.
The Electrical Safety Analyzer can of course also be operated manually through a spin-press button, similar to GPS systems used in automobiles. The following operating modes are available: Manual, Remote RS232/USB, Digital and Ethernet. Each Electrical Safety Analyzer can be remote controlled through a comfortable testing software. The GOOD-BAD results will be saved automatically on your databank. Electrical Safety Analyzers will be delivered including a leakage current test in case the device needs to be used in accordance with the medical-technical norm EN 60601. The Electrical Safety Testers of the 60335 series are easy to integrate at the workplace and laboratory.
- Devices: 36 & 400
- 7-pole (Sense/Source/Good/Bad/24V)
- PE plug: PES7
- Open end for self assembly
- Operation current: 32 A AC
- Max current: 32A AC
- Length: 10 m
- PE test lead, 2-pole
- Source path with 6mm plug for insertion to the device
- Sense path with BNC-plug for insertion to the device
- Devices: 400 series
- Start via control-IO
- With plug: 12-pole
- Access to control interface
- Cable length: 2m
- Side mounting for test waggon or table
- Ergonomically placed
- Probe type: VP400
- Side: left
- Colour: black
- Devices: 400 series
- Start via control-IO
- With plug: 12-pole
- Access to control interface
- Cable length: 2m
- With magnetic switch
- With screw joint for connection of a cable socket
- For magnetic contacting
- Devices: series 36 & 400
- Complete library
- License for 1 test system
- Including CD with drivers and manual
- Including cable-set for safety tester:
400 series (ST400), UX36, UH36 - Ergonomically design housing
- Voltage: 6 KVAC, 8 KVDC
- 2 pressure clamps L/N and PE
- 230V socket or others on demand
- Connecting cable: 2 m
- 4-wire-technique
- Start-Stop-function
- Result indication LED
- Cable length: 2m
- Max current: 32A AC
- Length: 15 m
- PE test lead, 2-pole
- Source path with 6mm plug for insertion to the device
- Sense path with BNC-plug for insertion to the device
- Including cable-set for safety tester:
400 series (ST400), UX36, UH36 - Ergonomically design housing
- 3 pressure clamps L,N and PE
- 230V socket or others on demand
- Connecting cable: 2 m
- Four pole
- Cable length: 2 - 6m
- Schuko plug
- Used for ground bond tester RS36 and
Isulation resistance tester MR36
Process of Testing with a Safety Tester
The testing process with a safety tester is as follows: connect the test object once, select the test program (optionally automatic via barcode), perform the test, and store the protocol data. Of course, the VDE test device can also be operated manually using the rotary-push knob – just like using a GPS in a car.
Modular Configuration of Your Safety Tester
As previously mentioned, electrical safety tests must be carried out in accordance with standards. Each standard defines a specific test setup that must be followed when testing a device under test. Since these setups can vary greatly, Sourcetronic offers you the option to configure your own measuring instrument. With a wide range of test modules such as high voltage, insulation, protective conductor, leakage current, and functional test, you can perform almost any standard-compliant test according to VDE, EN, or UL. Configure your own ST400!
Support for Different Operating Modes
The operating modes Manual, Remote RS232/USB, Digital, and Ethernet are available. With the convenient test technology software, you can remotely control any VDE test device. The PASS–FAIL results are automatically stored as XML files in your database. For the medical standard EN 60601, you receive the VDE test device with leakage current testing. Whether in the workshop, laboratory, or serial production, the 60335 safety testers can be integrated quickly and easily.
Product Overview: Buy Safety Testers