Certified quality management system
Safety Tester
If you need to carry out electrical safety test in accordance with EN 60335, EN 61010, EN 60601, EN 60598 or other national and international norms, then you are at the right place. EN 60335 is a European regulation for safety of electrical devices. Tests in accordance with EN 60335; e.g. the protective conductor test, high voltage test and function test, are carried out on the whole device after assembly.
The robust, fully automatic Electrical Safety Tester ST400 ensures fast testing cycles incl. documentation (backtracking of data – Traceability). In addition to that, the ST400 Electrical Safety Tester also disposes two USB- Interfaces, LAN, RS232 and digital, as well as analogue I/O ports. I/O tests are ideally used to automatically pilot external systems. The test procedure with an Electrical Safety Tester results as follows: Connect the testee (device under test), chose the settings for the test program (automatic barcode if provided), test and save test protocol.
The Electrical Safety Analyzer can of course also be operated manually through a spin-press button, similar to GPS systems used in automobiles. The following operating modes are available: Manual, Remote RS232/USB, Digital and Ethernet. Each Electrical Safety Analyzer can be remote controlled through a comfortable testing software. The GOOD-BAD results will be saved automatically on your databank. Electrical Safety Analyzers will be delivered including a leakage current test in case the device needs to be used in accordance with the medical-technical norm EN 60601. The Electrical Safety Testers of the 60335 series are easy to integrate at the workplace and laboratory.
- PE test lead, 4-pole, grey (D = 7.5 mm), with open cable end for self-assembly
- PE plug PES4, 4-pin, for plugging into the test instrument
- Max. operating current for PE tests: 32 A AC (source path)
- Selectable cable length: 2 m, 3 m or 5 m (other cable lengths on request)
- PE test lead, 4-pole, grey (D = 7.5 mm), with open cable end for self-assembly
- PE plug PES4, 4-pin, for plugging into the test instrument
- Max. operating current for PE tests: 32 A AC (source path)
- Selectable cable length: 2 m, 3 m or 5 m (other cable lengths on request)
- PE test lead, 2-pole, black (D = 8.5 mm)
- Solid cable lug for contacting or screwing on, e.g. to a contact clamp or a coupling prism
- Source path with 6 mm plug for plugging into the test instrument (single-pole)
- Sense path with BNC plug for plugging into the test instrument
- Max. operating current: source path 100 A AC
- Selectable cable length: 2 m, 3 m, 5 m or 10 m (other cable lengths on request)
- PE test lead, 7-pole, grey (D = 8.5 mm), with open cable end for self-assembly
- PE plug PES7, 7-pin, for plugging into the test instrument
- Max. operating current for PE tests: 32 A AC (source path)
- Selectable cable length: 2 m, 3 m, 5 m or 10 m (other cable lengths on request)
- PE test lead, 7-pole, grey (D = 8.5 mm)
- PE plug PES7, 7-pin, for plugging into the test instrument
- Opposite end with 4 mm lamella plug, e.g. for attaching a test clamp
- Max. operating current for PE tests: 32 A AC (source path)
- Selectable cable length: 2 m, 3 m, 5 m or 10 m (other cable lengths on request)
- Test cage with transparent hood for test instruments of the 36 series
- Fully assembled with safety switch (2 paths)
- Positive protection against contact per EN 50191
- Gas springs for damping and end-position damping
- Interior (W x H x D): 330 x 350 x 450 mm
- Test connections HV1 and HV2/PEX1 with safety sockets and quick-action test clamps
- Connecting leads for the test instrument included (safety circuit, 2 x HV cable, 2 m)
- IP30, weight: 14.5 kg
- Max. rated values HV/ISO: 7 kV AC / 10 kV DC, max. 10 A
- Test cage with transparent hood for test instruments of the 36 series
- Fully assembled with safety switch (2 paths)
- Positive protection against contact per EN 50191
- Gas springs for damping and end-position damping
- Interior (W x H x D): 550 x 350 x 450 mm
- Test connections HV1 and HV2/PEX1 with safety sockets and quick-action test clamps
- Connecting leads for the test instrument included (safety circuit, 2 x HV cable, 2 m)
- IP30, weight: 19.0 kg
- Max. rated values HV/ISO: 7 kV AC / 10 kV DC, max. 10 A
- Test cage with transparent cover
- Completely assembled with safety switch (2 paths)
- Mandatory protection against accidental contact according to EN 50191
- Gas springs for damping and end-position damping
- Interior (W x H x D): 800 x 350 x 450 mm
- Safety switch connections terminated on terminal block
- IP30, weight: 21.3 kg
- Max. rated values HV/ISO: 7 kV AC / 10 kV DC, max. 10 A
- Test cage with transparent hood
- Fully assembled with safety switch (2 paths)
- Positive protection against contact per EN 50191
- Gas springs for damping and end-position damping
- Interior (W x H x D): 1,000 x 350 x 450 mm
- Safety switch connections wired to contact terminal
- IP30, weight: 24 kg
- Max. rated values HV/ISO: 7 kV AC / 10 kV DC, max. 10 A
- Test cage with transparent hood
- Completely assembled with safety switch (2 channels)
- Mandatory protection against accidental contact according to EN 50191
- Gas springs for damping and end-position damping
- Interior (W x H x D): 650 x 530 x 600 mm
- Safety switch connections terminated on terminal block
- IP30, Weight: 27 kg
- Max. rated values HV/ISO: 7 kV AC / 10 kV DC, max. 10 A
- Test cage with transparent hood
- Completely assembled with safety switch (2 paths)
- Mandatory contact protection according to EN 50191
- Gas springs for damping and end-position damping
- Interior (W x H x D): 800 x 530 x 600 mm
- Safety switch connections applied to contact terminal
- IP30, weight: 27 kg
- Max. rated values HV/ISO: 7 kV AC / 10 kV DC, max. 10 A
- Test cage with transparent hood
- Completely assembled with safety switch (2 paths)
- Inevitable protection against accidental contact according to EN 50191
- Gas springs for damping and end-position damping
- Interior (W x H x D): 1,000 x 530 x 600 mm
- Safety switch connections connected to terminal block
- IP30, weight: 39 kg
- Max. rated values HV/ISO: 7 kV AC / 10 kV DC, max. 10 A
Process of Testing with a Safety Tester
The testing process with a safety tester is as follows: connect the test object once, select the test program (optionally automatic via barcode), perform the test, and store the protocol data. Of course, the VDE test device can also be operated manually using the rotary-push knob – just like using a GPS in a car.
Modular Configuration of Your Safety Tester
As previously mentioned, electrical safety tests must be carried out in accordance with standards. Each standard defines a specific test setup that must be followed when testing a device under test. Since these setups can vary greatly, Sourcetronic offers you the option to configure your own measuring instrument. With a wide range of test modules such as high voltage, insulation, protective conductor, leakage current, and functional test, you can perform almost any standard-compliant test according to VDE, EN, or UL. Configure your own ST400!
Support for Different Operating Modes
The operating modes Manual, Remote RS232/USB, Digital, and Ethernet are available. With the convenient test technology software, you can remotely control any VDE test device. The PASS–FAIL results are automatically stored as XML files in your database. For the medical standard EN 60601, you receive the VDE test device with leakage current testing. Whether in the workshop, laboratory, or serial production, the 60335 safety testers can be integrated quickly and easily.
Product Overview: Buy Safety Testers