-
Measurement Technology
- Rental Equipment
- Battery tester
- Calibration Services
- Capacitance Meter
- DC Bias Current Source
- Digital Power Meter
- Earth Tester
- Ground Bond Tester
- HV Probe
- High Voltage Relays
- Hipot tester
- Impedance Analyzer
- Insulation Tester
- LCR Meter
- Measurement Software
- Megohmmeter
- Microohmmeter
- Milliohmmeter
- Multimeter
- Relay Matrix
- Safety Tester
- Surge Tester
- Test Systems
- Transformer Tester
- Transport Cases
Microohmmeter MPK-215R (Rental device)
€379.00*
Details
+49 421 277 9999
Highlights
- 200 A Low-Resistance-Meter
- Direct reading 4 ½ digits
- Resolution: 0.1 µOhm
- Resistance reading up to 1 Ohm
- 200 A test current
- Powered by internal battery or main
- Overheating protection
- USB Port
- Bluetooth
- Protection IP54
- Comfortable Software ST®Logger (optional)
The MPK-215R is a portable, microprocessor controlled instrument, used to accurately measure very low contact resistances of breakers and switches, busbars, transformers winding and engines, etc, with test currents from 5 A to 200 A. It employs the 4 terminals-method to avoid measurement errors caused by test leads and their contact resistances. Resistances readings are shown in the alphanumeric display with up to 4½ digits resolution. It allows to measure resistances up to 1 Ω, with a resolution of up to 0.1 μΩ.
Measurement accuracy is guaranteed by an state-of-the-arts signals amplification system, offset-free and of high long-term stability. Test current may be adjusted by the operator in every one of the scales and their values are measured using an analog indicator (bargraph), making it easy to measure resistances with a significant inductive component, as in the case of big transformers windings. The high-current generation system is based on modern technology that allows to significantly decrease both its weight and size.
The cabinet is made of plastic material highly resistant to impacts and to environmental challenges. Internal thermal sensors in all sensitive components avoid any damaged caused to the instrument due to overheating. This is a strong but lightweight equipment, and may be easily carried by one person. It is water-resistant and can be used under severe weather conditions offering an excellent performance working both in the laboratory and out in the field.
TEST CURRENT
- 5 A up to 200 A (True DC)
RESISTANCE RANGES
- 0.1 μΩ to 2 mΩ, with 0.1 μΩ resolution
- 2 mΩ to 200 mΩ, with 10 μΩ resolution
- 200 mΩ to 1 Ω, with 1 mΩ resolution
MEASUREMENT PRINCIPLE
- Four-terminal, U/I
PROTECTIONS
- Overcurrent, short-circuit and overheating
PROGRAMMABLE TEST TIME
- Allows to setup the test time from 5 seconds up to 120 seconds
BASIC ACCURACY
- ±1% of measured value.
ADVANCED FEATURES
- Digital direct reading of very low resistances in the alphanumerical display, with up to 4½ digits
- Very fast and accurate measurements
BUILT-IN MEMORY
- Capacity to store 50 registers with 80 readings each
BLUETOOTH
- For configuration and control
INTERFACE
- USB
ST-LOGGER SOFTWARE
- Friendly, easy to use software.
- With automatic report generator, including the operator's commentaries
ENVIRONMENTAL PROTECTION
- IP65 (with closed lid)
SAFETY CLASS
- Meets the requirements of IEC 61010-1
POWER SUPPLY
- Mains: 100-240 V~ 60 Hz
OPERATING TEMPERATURE RANGE
- 23°F to 122°F (-5°C to 50°C)
STORAGE TEMPERATURE RANGE
- -14°F to 140°F (-10°C to 60°C)
HUMIDITY RANGE
- 95 % RH (non condensing)
EQUIPMENT WEIGHT
- Approx. 24.25 lb (11 kg)
DIMENSIONS
- 19.76" x 15.51" x 7.48" (502 x 394 x 190 mm)
ACCESSORIES WEIGHT
- Approx. 45.19 lb (20.5 kg)
INCLUDED ACCESSORIES
- 1 Set of combined test leads (current and potential), equipped with C-clamps (Sargent)
- 1 Ground cable
- 1 Power cord
- 1 USB cable
- 1 Carrying case the test leads
- 1 License to use the software ST-Logger
- 1 User guide